The Basics of Plumbing Knowledge for Bathtub Installation
The Basics of Plumbing Knowledge for Bathtub Installation
Blog Article
Were you hunting for tips about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Setting up a bathtub isn't specifically brain surgery, however it does require strong plumbing, carpentry, and also often, tiling skills. Changing an old tub with a brand-new one is likewise a reasonably challenging task. If the old tub is readily easily accessible, the project can move easily; if you need to open a wall to get rid of the old tub and position the new bathtub, the job is a lot harder. In either case, the project is within a home handyman's skills, although you will certainly need an assistant to move out the old bathtub as well as embeded in the new one. See to it you have actually qualified on your own for the job and also are comfortable attempting it. As opposed to working with a service provider to take over a halfway-completed project, it is far better to consider utilizing one prior to you begin. Opportunities are you may require a specialist plumber to make tube links.
This article will certainly assist you set up a new bath tub in your restroom if you have actually already gotten a new tub and also do not require to change the plan of your previous supply of water pipes.
Your tools and product checklist ought to make up the following:
Planning for the Installment
Firstly, the supporting frame provided with the bathroom must be fitted (if required) according to the manufacturer's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is important to see to it that if the faucet features a plastic washing machine, it is fitted in between the bath as well as the faucets. On a plastic bath, it is likewise sensible to fit a supporting plate under the taps device to stop stress on the bathtub.
Fit the flexible tap adapters to the bottom of both taps making use of 2 nuts as well as olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet via the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. Make sure you make use of all of the supplied washing machines.
Link the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bathroom ought to currently prepare to be fitted in its last placement.
Removing Old Taps
If you require to change old faucets with brand-new ones as a part of your setup, after that the first thing you need to do is detach the water. After doing so, switch on the taps to drain any water remaining in the system. The process of eliminating the existing taps can be rather problematic as a result of the restricted accessibility that is commonly the instance.
Use a container wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipes to the taps. Have a cloth ready for the staying water that will certainly come from the pipelines. When the supply pipelines have been eliminated, use the same device to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the single faucets from turning throughout this process. Once the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing substance.
Before moving on to fit the brand-new taps, contrast the pipeline connections on the old taps to the new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the brand-new faucets to fit.
Mounting the Tub
Using both wooden boards under its feet, put the tub in the called for placement. The wood boards are practical in evenly spreading the weight of the tub over the location of the boards as opposed to focusing all the weight onto 4 tiny factors.
The following objective is to make sure that the tub is leveled all round. This can be accomplished by inspecting the spirit level as well as changing the feet on the tub up until the level checks out degree.
To set up taps, fit all-time low of the furthest flexible faucet adapter to the appropriate supply pipe by making a compression sign up with; after that do the exact same for the other faucet.
Activate the supply of water as well as examine all joints as well as brand-new pipework for leakages and tighten them if needed. Load the bath tub and likewise inspect the overflow outlet and the typical electrical outlet for leaks.
Lastly, repair the bathroom paneling as defined in the maker's instruction manual. Tiling and also sealing around the tub needs to wait up until the tub has actually been used a minimum of when as this will certainly settle it into its last placement.
Fitting New Taps
If the tails of the brand-new taps are plastic, after that you will certainly require a plastic port to prevent damage to the string. One end of the port fits on the plastic tail of the faucet as well as the various other end supplies a link to the current supply pipes.
If you require to fit a monobloc, after that you will require reducing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, position the tap in the placing hole in the bath/basin guaranteeing that the washers remain in place between the faucet and also the sink. Safeguard the tap in place with the supplier offered backnut. Once the faucet is firmly in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with regular tap connectors. The former kind must be attached to the faucet finishes initially, tightening only by hand. The supply pipelines can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bathtub
In the location where the bathroom satisfies the tile, it is needed to secure the joins with a silicone rubber caulking. This is essential as the installation can move sufficient to fracture a rigid seal, triggering the water to permeate the wall surface in between the bathroom and the tiling, bring about problems with moisture as well as feasible leaks to the ceiling listed below.
You can pick from a selection of coloured sealers to blend in your components as well as fittings. They are marketed in tubes as well as cartridges, and can securing voids up to a size of 3mm (1/8 inch). If you have a larger space to fill, you can load it with twists of drenched paper or soft rope. Keep in mind to always fill up the bath tub with water before sealing, to allow for the movement experienced when the tub remains in usage. The sealant can crack fairly early if you do not consider this activity prior to securing.
Additionally, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally quickly readily available on the marketplace. It is advisable to fit the ceramic tiles using waterproof or water resistant adhesive and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm very intrigued by A Step-by-Step Guide to Installing a Bathtub and I hope you enjoyed reading the blog posting. Enjoyed our blog entry? Please share it. Help someone else check it out. Thank you so much for your time spent reading it.
Book Your Installation Report this page